IP addressing for your VPCs and subnets
IP addresses enable resources in your VPC to communicate with each other, and with resources over the internet.
Classless Inter-Domain Routing (CIDR) notation is a way to represent an IP address and its network mask. The format of these addresses is as follows:
-
An individual IPv4 address is 32 bits, with 4 groups of up to 3 decimal digits. For example, 10.0.1.0.
-
An IPv4 CIDR block has four groups of up to three decimal digits, 0-255, separated by periods, followed by a slash and a number from 0 to 32. For example, 10.0.0.0/16.
-
An individual IPv6 address is 128 bits, with 8 groups of 4 hexadecimal digits. For example, 2001:0db8:85a3:0000:0000:8a2e:0370:7334.
-
An IPv6 CIDR block has four groups of up to four hexadecimal digits, separated by colons, followed by a double colon, followed by a slash and a number from 1 to 128. For example, 2001:db8:1234:1a00::/56.
For more information, see What is CIDR?
Contents
Private IPv4 addresses
Private IPv4 addresses (also referred to as private IP addresses in this topic) are not reachable over the internet, and can be used for communication between the instances in your VPC. When you launch an instance into a VPC, a primary private IP address from the IPv4 address range of the subnet is assigned to the default network interface (eth0) of the instance. Each instance is also given a private (internal) DNS hostname that resolves to the private IP address of the instance. The hostname can be of two types: resource-based or IP-based. For more information, see EC2 instance naming. If you don't specify a primary private IP address, we select an available IP address in the subnet range for you. For more information about network interfaces, see Elastic Network Interfaces in the Amazon EC2 User Guide.
You can assign additional private IP addresses, known as secondary private IP addresses, to instances that are running in a VPC. Unlike a primary private IP address, you can reassign a secondary private IP address from one network interface to another. A private IP address remains associated with the network interface when the instance is stopped and restarted, and is released when the instance is terminated. For more information about primary and secondary IP addresses, see Multiple IP Addresses in the Amazon EC2 User Guide.
We refer to private IP addresses as the IP addresses that are within the IPv4 CIDR range of the VPC. Most VPC IP address ranges fall within the private (non-publicly routable) IP address ranges specified in RFC 1918; however, you can use publicly routable CIDR blocks for your VPC. Regardless of the IP address range of your VPC, we do not support direct access to the internet from your VPC's CIDR block, including a publicly-routable CIDR block. You must set up internet access through a gateway; for example, an internet gateway, virtual private gateway, a Amazon Site-to-Site VPN connection, or Amazon Direct Connect.
We never advertise the IPv4 address range of a subnet to the internet.
Public IPv4 addresses
All subnets have an attribute that determines whether a network interface created in the subnet automatically receives a public IPv4 address (also referred to as a public IP address in this topic). Therefore, when you launch an instance into a subnet that has this attribute enabled, a public IP address is assigned to the primary network interface (eth0) that's created for the instance. A public IP address is mapped to the primary private IP address through network address translation (NAT).
Note
Amazon charges for all public IPv4 addresses, including public IPv4 addresses
associated with running instances and Elastic IP addresses. For more information, see the Public IPv4 Address
tab on the Amazon VPC pricing page
You can control whether your instance receives a public IP address by doing the following:
-
Modifying the public IP addressing attribute of your subnet. For more information, see Modify the IP addressing attributes of your subnet.
-
Enabling or disabling the public IP addressing feature during instance launch, which overrides the subnet's public IP addressing attribute.
-
You can unassign a public IP address from your instance after launch by managing the IP addresses associated with a network interface. For more information, see Manage IP addresses in the Amazon EC2 User Guide.
A public IP address is assigned from Amazon's pool of public IP addresses; it's not associated with your account. When a public IP address is disassociated from your instance, it's released back into the pool, and is no longer available for you to use. In certain cases, we release the public IP address from your instance, or assign it a new one. For more information, see Public IP addresses in the Amazon EC2 User Guide.
If you require a persistent public IP address allocated to your account that can be assigned to and removed from instances as you require, use an Elastic IP address instead. For more information, see Associate Elastic IP addresses with resources in your VPC.
If your VPC is enabled to support DNS hostnames, each instance that receives a public IP address or an Elastic IP address is also given a public DNS hostname. We resolve a public DNS hostname to the public IP address of the instance outside the instance network, and to the private IP address of the instance from within the instance network. For more information, see DNS attributes for your VPC.
If you are using Amazon VPC IP Address Manager (IPAM), you can get a contiguous block of public IPv4 addresses from Amazon and use it to allocate sequential Elastic IP addresses to Amazon resources. Using contiguous IPv4 address blocks can significantly reduce management overhead for security access control lists and simplify IP address allocation and tracking for enterprises scaling on Amazon. For more information, see Allocate sequential Elastic IP addresses from an IPAM pool in the Amazon VPC IPAM User Guide.
IPv6 addresses
As the internet continues to grow, so does the need for IP addresses. The most common format for IP addresses is IPv4. The new format for IP addresses is IPv6, which provides a larger address space than IPv4. IPv6 resolves the IPv4 address exhaustion issue and enables you to connect more devices to the internet. The transition is gradual, but as IPv6 adoption grows, you can simplify your networks and take advantage of IPv6 advanced capabilities for better connectivity, performance, and security.
Many Amazon services, such as Amazon EC2, Amazon S3, and Amazon CloudFront, offer either dual-stack (IPv4 and IPv6) or IPv6-only support, allowing resources to be assigned IPv6 addresses and accessed over the IPv6 protocol and simplifying network configuration and management for those customers adopting IPv6. Other services offer limited or partial dual-stack and IPv6-only support. For more information about services that support IPv6, see .
Note that some IPv6 addresses are reserved by the Internet Engineering Task Force. For more information about reserved IPv6 address ranges, see IANA IPv6 Special-Purpose Address Registry
Note
Both public and private IPv6 addressing is available in Amazon. Amazon considers public IP addresses those advertised on the internet from Amazon, while private IP addresses are not and cannot be advertised on the internet from Amazon.
Public IPv6 addresses
Public IPv6 addresses are IPv6 addresses that can be configured to remain private or configured to be reachable over the Internet.
These are some of the ways you can prepare to use public IPv6 addresses for your workloads:
-
Create an IPAM with Amazon VPC IP Address Manager and provision an Amazon-owned public IPv6 address range to an IPAM address pool. For more information, see Create IPv6 pools in the Amazon VPC IPAM User Guide.
-
If you have an IPAM and you own a public IPv6 address range, bring some or all of the public IPv6 address range to IPAM and provision the public IPv6 address range to an IPAM address pool. For more information, see Tutorial: Bring your IP addresses to IPAM in the Amazon VPC IPAM User Guide.
-
If you don't have an IPAM but you own a public IPv6 address range, bring some or all of the public IPv6 address range to Amazon. For more information, see Bring your own IP addresses (BYOIP) to Amazon EC2 in the Amazon EC2 User Guide.
Once you are prepared to use public IPv6 addresses, you can assign public IPv6 addresses to instances (see IPv6 addresses in the Amazon EC2 User Guide), you can allocate a public IPv6 CIDR block to your VPC (see Add or remove a CIDR block from your VPC) and associate the IPv6 CIDR block with your subnets (see Modify the IP addressing attributes of your subnet).
Private IPv6 addresses
Private IPv6 addresses are IPv6 addresses that are not advertised and cannot be advertised on the Internet from Amazon.
You can use a private IPv6 address if you want your private networks to support IPv6 and you have no intention of routing traffic from these addresses to the Internet. If you want to connect to the internet from a resource that has a private IPv6 address, you can, but you must route traffic through a resource in another subnet with a public IPv6 address to do so.
There are two types of private IPv6 addresses:
IPv6 ULA ranges: IPv6 addresses as defined in RFC4193
. These address ranges always start with “fc” or “fd”, which makes them easily identifiable. Valid IPv6 ULA space is anything under fd00::/8 that does not overlap with the Amazon reserved range fd00::/16. IPv6 GUA ranges: IPv6 addresses as defined in RFC3587
. The option to use IPv6 GUA ranges as private IPv6 addresses is disabled by default and must be enabled before you can use it. For more information, see Enable provisioning private IPv6 GUA CIDRs in the Amazon VPC IPAM User Guide.
Note the following:
-
Private IPv6 addresses are only available through Amazon VPC IP Address Manager (IPAM). IPAM discovers resources with IPv6 ULA and GUA addresses and monitors pools for overlapping IPv6 ULA and GUA address space.
-
When you use private IPv6 GUA ranges, we require that you use IPv6 GUA ranges owned by you.
Private IPv6 addresses are not and cannot be advertised on the internet by Amazon. Amazon does not allow direct egress to the public internet from a private IPv6 range even if there is an internet gateway or egress only internet gateway in the VPC. Private IPv6 addresses are automatically dropped at the internet gateway edge ensuring that they are not routed publicly.
Amazon reserves the first 4 subnet private IPv6 addresses and the last one.
Valid ranges for private IPv6 ULA are /9 to /60 starting with fd80::/9.
If you have a private IPv6 GUA range allocated to a VPC, you cannot use public IPv6 GUA space that overlaps the private IPv6 GUA space in the same VPC.
Communication between resources with private IPv6 ULA and GUA address ranges is supported (such as across Direct Connect, VPC peering, transit gateway, or VPN connections).
-
You can use private IPv6 addresses with IPv6-only and dual-stack VPC subnets, elastic load balancers and Amazon Global Accelerator endpoints.
There is no charge for private IPv6 addresses.
These are some of the ways you can prepare to use private IPv6 addresses for your workloads:
-
Create an IPAM with Amazon VPC IP Address Manager and provision a private IPv6 ULA range to an IPAM address pool. For more information, see Create IPv6 pools in the Amazon VPC IPAM User Guide.
-
Create an IPAM with Amazon VPC IP Address Manager and provision a private IPv6 GUA range to an IPAM address pool. The option to use IPv6 GUA ranges as private IPv6 addresses is disabled by default and must be enabled on your IPAM before you can use it. For more information, see Enable provisioning private IPv6 GUA CIDRs in the Amazon VPC IPAM User Guide.
Once you are prepared to use private IPv6 addresses, you can allocate a private IPv6 CIDR block from an IPAM pool to your VPC (see Add or remove a CIDR block from your VPC) and associate the IPv6 CIDR block with your subnets (see Modify the IP addressing attributes of your subnet).
Use your own IP addresses
You can bring part or all of your own public IPv4 address range or IPv6 address range to your Amazon account. You continue to own the address range, but Amazon advertises it on the internet by default. After you bring the address range to Amazon, it appears in your account as an address pool. You can create an Elastic IP address from your IPv4 address pool, and you can associate an IPv6 CIDR block from your IPv6 address pool with a VPC.
For more information, see Bring your own IP addresses (BYOIP) in the Amazon EC2 User Guide.
Use Amazon VPC IP Address Manager
Amazon VPC IP Address Manager (IPAM) is a VPC feature that makes it easier for you to plan, track, and monitor IP addresses for your Amazon workloads. You can use IPAM to allocate IP address CIDRs to VPCs using specific business rules.
For more information, see What is IPAM? in the Amazon VPC IPAM User Guide.